![xlite softphone makes calls but no sound xlite softphone makes calls but no sound](https://smartheart.in.ua/sites/default/files/x-lite-voip-softphone-calls-over-ip-200-200.jpg)
#XLITE SOFTPHONE MAKES CALLS BUT NO SOUND ANDROID#
Bria Android Tablet Edition 1.2 User Guide.Bria Android Tablet Edition 1.1 User Guide.Bria Android Tablet Edition 1.0.3 User Guide.Thanks again for your time and attention. I think I've had enough backtalk from machines today. I've rebooted the UCx, my laptop (I've got a couple VPNs I jump in and out of and sometimes I get weird network issues that a reboot clears), verified the edits to the config file are gone (they are, and the error from earlier about that config is gone), I've unregistered the softphone and reregistered, deleted and rebuilt the extension. So that leaves something to do with the UCx, but I removed the addition to sip_general_nf This Softphone was working fine, earlier, and still works fine registered to another UCx on the VPN. WARNING chan_sip.c: Hanging up call 79961MDQ0MTlmMGFhNDAyNDcwOTRhN2Q1YmNmMmEyMzAyNjk - no reply to our critical packet (see. Packet timed out after 6399ms with no response WARNING chan_sip.c: Retransmission timeout reached on transmission 79961MDQ0MTlmMGFhNDAyNDcwOTRhN2Q1YmNmMmEyMzAyNjk for seqno 2 (Critical Response) - See. VERBOSE file.c: - Playing 'demo-echotest.slin' (language 'en') The Log shows the following after I can see the UCx receive the digits and try to play a recording: It registers ok, shows up as Online in the Extension Report, but when I try to make a call from it, it's silent for a few seconds then disconnects. I went to add a recording of a ringtone, and discovered my XLite Softphone stopped working.
![xlite softphone makes calls but no sound xlite softphone makes calls but no sound](https://static.macupdate.com/screenshots/275391/m/x-lite-screenshot.png)
Unfortunatley, no word yet from the IT guy, so I decided to try the announcement-workaround. We always try to get the IT guy to forward all the ports we would like opened (and if you can forward one to 443 of the UCx you can configure that sucker from your smartphone!!!) We've got a doc we hand to the IT folk on installs, and the SIP ALG advisement is a part of it. RE: Calls forwarded outbound via SIP trunks connect but no audio ucxguy (Programmer) 24 Jun 16 20:10 I tried to enter the "progressinband = yes" under SIP settings, and it took the change, but the Ring Group scheme and the Misc Destination scheme both had the same old issue.Įntering the "progressinband = yes" into the config file works, but throws a scary-looking error under SIP Settings "ERRORS, Settings in /etc/asterisk/sip_general_nf may override these. VOIP.ms DID -> Test ext set to unconditional forward to my cell outdial VOIP.ms. VOIP.ms DID -> Inbound DID route -> Ring Group with my cell and outdial digit as member + #
![xlite softphone makes calls but no sound xlite softphone makes calls but no sound](https://switch2voip.us/wp-content/uploads/2015/05/switch2voip.us_images_xlite_002.gif)
VOIP.ms DID -> Inbound DID route -> Misc Dest for cell. I added that to the config file as you specified and reloaded.Ĭall forwarding w/audio WORKS OK using this: I already had the public IP and local network definitions, but I didn't have "progressinband = yes" RE: Calls forwarded outbound via SIP trunks connect but no audio Ringback is also absent during the no-audio call. I did a bit of looking around for REFER settings, but I can't find anything relevant on the E-Metrotel Documentation page, nor in the VOIP.ms portal. The Wireshark capture for the working call has RTP all over the place, and I can playback my audio with the Wireshark player.īasically, the UCx seems to be producing no audio at all when I'm trying to forward calls off-site via the SIP trunks (after having come into the system via the same SIP trunks). I can see the call setup, 200 OKs, 100 Trying, 183 Session progress, and finally the BYE, but no RTP. However, there's no RTP whatsoever during the no-audio call. I ran Wireshark captures for working/not-working calls, thinking that would give me enough information to reach out to the IT guy to show RTP was being sent by the UCx and must be getting blocked by their Sonicwall. UCx20 at 4.5 with latest updates (just applied them while working on this). (Using a softphone on my laptop registered via VPN during testing)Ī call inbound via SIP trunks then forwarded outbound with a Misc Destination to my cell via the one PoTS trunk on the system works fine. The call rings on the far-end, and can be answered, but there's no audio in either direction.Ī call inbound via SIP trunks to a SIP extension works just fine. Forwarding a call coming into the SIP trunks and then back out the SIP trunks results in no audio.